ZETRON 2000 Series Spezifikationen Seite 291
- Seite / 376
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
291
The “.CUS” Files
the “liu” ZlinkW command. More than one card - port pair can be selected with a single
trunk command, and at least one card - port pair must be specified.
TRUNK 7B ; select card 7 port B
;
; now select both ports A and B on cards 10 through 13
;
TRUNK 10A 10B 11A 11B 12A 12B 13A 13B
For each of the value setting commands there is a default value that all trunks will be set to
before the trunks.cus file is processed. The default values remain in effect until a selection
command is found. Any value not explicitly overridden in the trunks.cus file will be at its
default value when a Trunk command is encountered.
Table 44: Default Settings for TRUNKS.CUS File
An example of a trunks.cus file might be:
;
; Trunks.cus for Phast Phreddy's Phrantic Paging
;
GROUP 1 ; select Trunk Group 1 as current Trunk Group
TRUNK 7|0 ; all these trunks
TRUNK 7|1 ; are in
TRUNK 8|0 ; Trunk Group 1
; and use whatever the subscriber records contain for
; channel and zone information
GROUP 2 ; now switch to Trunk Group 2
CHANNEL 1 1 1 1 ; and select RF channel 1 as override channel
TRUNK 8|1 ; All these trunks
TRUNK 9|0 ; are in
TRUNK 9|1 ; Trunk Group 2
TRUNK 10|0 ; and have pages forced
TRUNK 10|1 ; to have channel set to 1
CHANNEL 3 3 3 3
TRUNK 11|0 ; this trunk is in Trunk Group 2 and pages are forced
; to channel 3
CHANNEL 2 2 2 2
TRUNK 11|1 ; this trunk is in Trunk Group 2 and pages are forced
; to channel 2
GROUP 3
CHANNEL * * * *
TRUNK 12A 12B 13A 13B 14A 14B ; these trunks are in trunk group 3
; and will use channel info from
Command Default Value Notes
Channel — use subscriber record's value for channels.
Zone — use subscriber record's value for zones.
Priority — use subscriber record's value for page priority.
Destinations — Use subscriber record's value for page destination.
AllowPrompt Both allow tone and, if installed, voice prompts.
Security enabled Enable Security Code checking on trunks.
Group 0 no trunk groups.
Supergroup — No Trunk Supergroup settings.
- Series 2000 Paging Terminals 1
- Installation and Maintenance 1
- Software License 2
- Limited Warranty 2
- Limitation of Liability 2
- Compliance Statements 3
- Safety Summary 3
- Release History 4
- 6 025-9035AA 6
- 8 025-9035AA 8
- Contents 10
- 10 025-9035AA 10
- 12 025-9035AA 12
- Purpose of This Manual 13
- Contents of This Manual 14
- System Specifications 16
- Model 2200EX 17
- Lightning Protection 17
- Operating Power 17
- 18 025-9035AA 18
- Digital T1 Interface 20
- General Specifications 21
- Electrical Specifications 22
- Voice System Specifications 23
- ADPCM Voice System (950-9061) 24
- System Installation 25
- Installation Checklist 26
- 28 025-9035AA 28
- Alignment Procedure 30
- 32 025-9035AA 32
- TELCO Ground Reference 33
- Pentium CPU Card 34
- Cable Routing 36
- 38 025-9035AA 38
- Model 2200EX Installation 39
- ♦ Setting up a Model 2200EX 40
- Model 2200 Main Chassis Setup 41
- Power Up Test 41
- 2000 Series Printer Option 42
- (15 foot cable) 43
- (red wire not used) 43
- Up = On 44
- Down = Off 44
- 46 025-9035AA 46
- 48 025-9035AA 48
- Configuration Using a Browser 50
- 52 025-9035AA 52
- 54 025-9035AA 54
- Overview 55
- Specifications 56
- Local Office Computer 56
- ♦ Installing ZbaseW on a PC 57
- ♦ Installing ZlinkW on a PC 57
- ♦ ZbaseW for additional PCs: 59
- ♦ Editing a Location 60
- ZlinkW Property Fields 62
- ♦ Exiting ZbaseW 64
- Changing ZlinkW Passwords 65
- Shared PC 66
- Database Operations 69
- Training and Classes 69
- 70 025-9035AA 70
- Trunk Cards and Connections 71
- TELCO Connectors 72
- Adjustment Procedures 77
- Hybrid Adjustment 78
- ♦ Call setup procedure 79
- ♦ Hybrid adjustment procedure 80
- Rows of pins 81
- Dial Click Card 82
- Alarm Option 83
- Large RAM 84
- 4-Wire Audio E&M 84
- 86 025-9035AA 86
- Jumper Matrix Settings 87
- SINGLE TRUNK 88
- SIDE VIEW OF CARD MATRIX 88
- PLUG AND CONNECTORS 88
- ♦ Installing a DID line 90
- Operator Local Station 91
- 92 025-9035AA 92
- 94 025-9035AA 94
- 96 025-9035AA 96
- Radio Connectors 98
- Switch Settings 105
- Jumper Settings 106
- Station Card Adjustments 107
- Radio System 108
- 108 025-9035AA 108
- Radio Signal Descriptions 109
- Co-located Radio Station 110
- 112 025-9035AA 112
- RF to Radio Site 113
- 114 025-9035AA 114
- (Clear to Page Analog) 115
- (Clear to Page Binary) 115
- UDS 202T Modem 116
- TX Link Controllers 117
- Quintron 1000 Exciter Hookup 118
- Multiport Serial TAP Input 119
- Option Details 120
- Information Needed 121
- Hardware Installation 121
- Connections 122
- Miscellaneous 122
- Software Configuration 123
- Multiport Configurations 124
- TYPE “B” DB 25 PIN 127
- SIGNAL DESCRIPTION 127
- UDS 202T Modem Hookup Example 128
- Multiport Wire List 130
- 132 025-9035AA 132
- TNPP Overview 133
- TNPP Details 133
- PagePage 135
- Types of Packets 136
- Types of Links 136
- Limitations of TNPP 137
- Our Current TNPP Limitations 137
- Port Configuration 138
- Network CUS Parameter File 140
- <ETB> byte was 144
- TAP Outdial 146
- OPARAM CDS Settings 147
- NETWORK.CUS Settings 147
- TAP Outdial Processing 148
- TAP Outdial Status 148
- Theory of Operation 149
- System Operation 150
- CPU Card (702-9176) 151
- 152 025-9035AA 152
- Modem Card (802-0041) 153
- 154 025-9035AA 154
- 156 025-9035AA 156
- MF Decoder Option 158
- Station Card 158
- Call Processing Flow Charts 159
- PABX Trunk (Tip-Ring Loop) 163
- PABX Tie-Trunk (E&M) 164
- Operator Local Phone 165
- TELCO Signal Descriptions 166
- 168 025-9035AA 168
- DID Configuration (024-0010A) 169
- 170 025-9035AA 170
- 172 025-9035AA 172
- Pulsed # 173
- Termination 174
- TX AUDIO 175
- 176 025-9035AA 176
- (Remote Control Mode = 04): 178
- Troubleshooting and Repair 179
- Procedures 179
- 180 025-9035AA 180
- Front Panel Lights 182
- Progress Tones 184
- DIP Switches and Matrix Plugs 184
- Recommended Maintenance 185
- 186 025-9035AA 186
- General Information 187
- Office Computer 187
- Serial Ports 188
- Modem Connect 189
- Modem Setup - Software 190
- ZbaseW Setup 192
- Running ZlinkW 192
- Troubleshooting 193
- Other Checks 194
- Machine/Environment 194
- 196 025-9035AA 196
- Voice Storage System 197
- Address Settings 198
- “Old” ADPCM Card (702-9153) 199
- Audio Level 200
- ♦ Adding upgrade ICs 201
- Adding Second ADPCM Card 202
- Operation 203
- Record/Play 204
- Silence Deletion 204
- Maintenance 205
- 206 025-9035AA 206
- Single Files 207
- Client Prompts 208
- ♦ Installing the RAID drive 210
- RAID Hard Drive 211
- ♦ Installing the IDE drive 212
- Voice Prompts 213
- ♦ Batch file procedure 214
- ♦ Duplication procedure 215
- 216 025-9035AA 216
- System Configuration Files 217
- CONFIG.CDS File 218
- OPARAM.CDS File 218
- File Format for OPARAM.CDS 219
- Trunk Card OPARAM Codes 219
- 222 025-9035AA 222
- 224 025-9035AA 224
- TANS, and TDIS 227
- Station Card OPARAM Codes 229
- 230 025-9035AA 230
- 232 025-9035AA 232
- 234 025-9035AA 234
- 236 025-9035AA 236
- 238 025-9035AA 238
- 240 025-9035AA 240
- 8TNPP8C3 242
- Node Table Programming 243
- Port Programming 244
- 246 025-9035AA 246
- Physical Node ID 247
- Sample OPARAM.CDS 248
- Enhanced Packet Routing 248
- TAP Outdial OPARAM Codes 251
- 252 025-9035AA 252
- 254 025-9035AA 254
- 256 025-9035AA 256
- Modem-related Parameters 257
- Modem Programming Strings 258
- The “.CUS” Files 260
- Remote Maintenance 262
- 264 025-9035AA 264
- FileProbes CC 20 SDB 20 264
- ; between 1 and 255 267
- Generic Function Codes 277
- 278 025-9035AA 278
- Load Management 281
- 282 025-9035AA 282
- Commands within TRUNKS.CUS 284
- 286 025-9035AA 286
- ANIsend LogOn PIoff NoteOff 287
- Commands within NETWORK.CUS 294
- 296 025-9035AA 296
- Types of Events 300
- Actions Taken 301
- EVENTS.CUS 301
- Events Table 302
- NETWORK.CUS 303
- Log Posting 304
- 306 025-9035AA 306
- Installing ZlinkW 308
- Starting and Exiting ZlinkW 308
- ♦ Exiting ZlinkW: 309
- ZlinkW Properties Fields 310
- 312 025-9035AA 312
- Modem Connections 313
- Local Connections 313
- ZlinkW Command Reference 314
- 316 025-9035AA 316
- 318 025-9035AA 318
- 320 025-9035AA 320
- ZlinkW File Operations 321
- ZlinkW “cards” 322
- ZlinkW “date” 324
- ZlinkW “dos” 324
- ZlinkW “faultoff” 324
- ZlinkW “get” 324
- ZlinkW “lastboot” 325
- ZlinkW “liu” 325
- ZlinkW “log” 328
- ZlinkW “logopen” 328
- ZlinkW “ls” 329
- 330 025-9035AA 330
- ZlinkW Mailbox 331
- ZlinkW “newsdb” 331
- ZlinkW “niu” 331
- 332 025-9035AA 332
- ZlinkW “note” 334
- ZlinkW “page” 335
- ZlinkW “reboot” 338
- ZlinkW “repeat” 338
- ZlinkW “search” 339
- ZlinkW “siu” 340
- ZlinkW “tail” 342
- ZlinkW “time” 342
- ZlinkW “traffic” 342
- ZlinkW “vls” 343
- ZlinkW “vget”, “vput” 344
- ZlinkW Command Switches 345
- Date & Time Switches 345
- Log Posting Format 346
- Paging Format Letters 347
- 348 025-9035AA 348
- New Destination Type (Log +) 349
- “set” Command 350
- Classes of Calls 352
- Results of Calls 354
- Failure Results 355
- Warning Results 356
- Error Results 357
- Typical Bootup Sequence 358
- Paging Traffic Display 359
- 360 025-9035AA 360
- Definitions 362
- Protocol 362
- Initial Logon Sequence 363
- Transferring Pages 364
- Checksum Example 366
- Control Codes 367
- Printable Characters 368
- Appendix C: Decimal to HEX 369
- Conversion 369
- Examples 370
- 372 025-9035AA 372
- 374 025-9035AA 374
- 376 025-9035AA 376
Verwandte Produkte und Handbücher für POS-Terminals ZETRON 2000 Series
POS-Terminals ZETRON 2000 Series Spezifikationen
(31 Seiten)
(31 Seiten)
POS-Terminals ZETRON 2000 Series Spezifikationen
(232 Seiten)
(232 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern